Skip to content
SearchFree account
Menu
Article

Check engine light steady or flashing: what is the difference and what do you do?

A check engine light that stays on is not the same as one that flashes. This is how you tell the difference, what you can do yourself, and when to go to a garage.

Published on 14 November 20268 minute read

In short

  • The may not be red. The difference is not in the colour, but in whether it stays on or flashes.
  • If it stays on, the car has stored a fault. Have the car checked soon.
  • If it flashes, there is a serious problem, such as an engine so badly that the can be damaged. Drive gently, stop as soon as it is safe and look in the owner's manual.
  • Whether the light is flashing, you can only see on your dashboard. You can read the yourself, with a plug-in and your phone.

How the light should work

When you switch the ignition on, the comes on for a moment. This shows you that the light works. When you start the engine and there is no fault, it goes off again.

Under the European rules, the light may not be red. You see an orange or yellow engine symbol. There is one light for all faults that affect emissions. So the light itself does not tell you what is wrong. It does tell you how urgent it is: steady or flashing.

The light stays on: a fault has been stored

If the light stays on, the car's computer has found a fault and stored a . It can be something small, like a fuel cap that is not closed properly. It can also be an , or something in the electronics that control the fuel injection and the ignition.

There is no need to panic. But waiting is not a good plan either. If you keep driving with the light on, the system that keeps the exhaust gases clean can be damaged. The car may then drive worse or use more fuel.

The light flashes: the problem is more serious

If the light flashes, the problem is more serious than when it stays on. One example is an engine so badly that the can be damaged.

A means that the fuel in a does not burn. This can be because there is no spark, the wrong amount of fuel or too little pressure in the . The car's computer can notice this from small differences in how fast the engine turns.

If the so often that the can be damaged, the European rules say the light must warn in a different way, for example by flashing.

If the stops, the flashing stops. The light may then simply stay on, and the may stay stored. So the flashing stopping does not mean the fault is gone.

What to do if the light flashes

  1. Drive gently: not fast, and not with a trailer or a heavy load.
  2. Stop as soon as it is safe, in a safe place.
  3. Look in the owner's manual to see what your manufacturer says about a flashing .
  4. Stop in a safe place and call your breakdown service.
  5. Are you stopped in a safe place? Then you can read the , with the ignition on. That way you know what it is about when you speak to the garage or breakdown service.

What to do if the light stays on

  1. Adjust your speed. Stop in a safe place and see what is going on. If a red light is on as well, pull over straight away.
  2. Pay attention to how the car drives and write it down: when did the light come on, and did the car drive differently? This helps the garage.
  3. Check the oil level and the .
  4. At your next fill-up, check that the fuel cap is closed properly.
  5. Read the . Then you know which system it is about.
  6. Make an appointment at a garage soon. If the light does not go off after a few short trips with the fuel cap closed properly, do not wait any longer.

What the fault code tells you

A comes with a code from the P0300 series. P0300 means: the engine is . If the car can tell which it is, you also see a code per : P0301 for 1, P0302 for 2, and so on.

The code points to what is happening, not to the broken part. With a , it can be a dirty , the fuel or something else, for example. Under the European rules, the car does not always have to say which is .

So save the as well. This is a of things like the , the and the road speed at the moment the fault happened. A garage can use it to see under which conditions things went wrong.

What you can do yourself, and what you leave to the garage

  • Yourself: read the , check the fuel cap, look at the oil level and the , and write down when the light came on and how the car drove.
  • Yourself: save the , so the garage can see it too.
  • Not yourself: clear the code to make the light go off. Clearing fixes nothing. If the fault is still there, the light comes back on as soon as the car sees it again. Clearing can also delete the .
  • For the garage: find the cause and fix it. Only then do you clear the code and see whether it stays away.

When to go to a garage

If the light flashes, it is urgent. Have the car checked as soon as possible, and drive it as little as possible.

If the light stays on, make an appointment soon. If you leave a fault, the damage can get bigger and the repair more expensive.

If the light goes off by itself, you usually don't need to do anything. The car may switch the light off if it no longer sees the fault for three trips in a row. If the light comes back, do go to a garage. The may stay stored in the car for a while. Then the garage can still read it later.

What Car-Z can and cannot see

Through the , the car only reports whether the light is on or off. So whether it flashes, you see on your dashboard and not in the app.

Reading the is free: the , the and the , each with a short explanation in plain language. Also free: a warning if the engine overheats or the stops charging the battery, and clearing codes properly after the repair. You can only clear codes when the car is standing still, with the ignition on and the engine off. First, Car-Z saves a on your phone.

With Plus you also see the , whether the car says the light is on and, if your car reports it, how many kilometres you have driven with the light on. With Plus, Car-Z keeps track per car of when you first and last saw a code. That way you see whether a fault comes back.

Frequently asked questions

Can I keep driving if the check engine light stays on?

According to a large Dutch breakdown service, with an orange light you can drive on for a little while, at a lower speed, and go to a garage soon. Do stop in a safe place to see what is going on. If a red light comes on as well, pull over straight away.

The flashing stopped by itself. Is the problem gone now?

Not necessarily. When the stops, the flashing stops, but the light may stay on. The may also stay stored. So have the car checked anyway.

Can I turn the light off by clearing the fault code?

Yes, but that fixes nothing. If the fault is still there, the light comes back on as soon as the car sees it again. Clearing can delete the . Only clear after the repair.

My car is a diesel. Does flashing mean the same thing?

Not always. The European rule about flashing for was written for petrol engines. On a diesel, flashing can be about the , for example. Your car's owner's manual says what it means and what to do.

The light went off by itself after a few days. Do I need to do anything?

Usually not. The car may switch the light off if the fault does not happen for a few trips in a row, for example after you have closed the fuel cap properly. If the light comes back, have the car checked.

Sources

  1. Directive 70/220/EEC, Annex XI: OBD system (warning light, flashing for misfires, storing and clearing fault codes)European Union (text on legislation.gov.uk), consulted on 14 November 2026
  2. Do you drive a 1996 or newer car or light truck? (EPA420-F-02-016)U.S. Environmental Protection Agency (archive), consulted on 14 November 2026
  3. Waarschuwingslampje: stoppen of doorrijden?ANWB (Netherlands), consulted on 14 November 2026
  4. Warning and Indicator Lights, 2025 Hyundai Tucson (owner's manual)Hyundai, consulted on 14 November 2026
  5. DTC P0300-P0304 (workshop information Saab 9-5, 2011)Saab Workshop Information System (online copy), consulted on 14 November 2026
  6. Fault handling I, catalytic converter damaging misfiring (workshop information Saab 9-5, 1998)Saab Workshop Information System (online copy), consulted on 14 November 2026
  7. Directive 70/220/EEC, Annex XI, Appendix 1: freeze frameEuropean Union (text on legislation.gov.uk), consulted on 14 November 2026
  8. OBD-II PIDs (overview of the data from SAE J1979)Wikipedia, consulted on 14 November 2026

Read it yourself with Car-Z

Put a plug into the OBD port and see on your device what the car itself reports. Testing whether your plug and car work and reading the fault codes is free, without an account.

All articles