Skip to content
SearchFree account
Menu
Article

Reading a Land Rover Defender: the new one (L663) and the classic (Td5, Puma)

Which Defender can you read with a standard OBD2 dongle? On the new Defender you see engine codes and live values. On the classic Td5 and Puma, you try it free first.

Published on 18 November 20267 minute read

In short

  • The new Defender (L663, from model year 2020) speaks standard . With a and your phone you read the engine and live values such as , and .
  • Make-specific values such as the gearbox temperature or the air suspension are not part of standard . From model year 2026, Land Rover also secures diagnostics with Secure Diagnostics.
  • We have not tested the classic Defender with the Td5 or the Puma ourselves. Whether your car talks to a standard , you see with the free connection check, before you take out a subscription.

Two kinds of Defender

There are two very different Defenders. The classic Defender was built until 29 January 2016. The new Defender (internally L663) was presented in September 2019 and has model year 2020 and later. They share the name, but the technology is completely different.

For reading the car, the engine matters most. On the classic Defender from 1998, that is the Td5 (five , until spring 2007) and after that the Puma: a 2.4 litre diesel from Ford from 2007 and a 2.2 litre from model year 2012. Don't know which engine you have? Check the owner's manual or ask your garage.

Why the classic Defender can be different

is the European diagnostic system that watches the parts for clean exhaust gases. Cars with use the same connector and the same way of talking. That is why one works in a great many cars.

For diesel cars, that requirement came in steps. Lighter diesel passenger cars had to have it from 2003 (new types) and 2004 (all). For heavy passenger cars (over 2500 kg or for more than six people) and for vans, it at first only applied to new types, from 2005 or 2006. Whether that applied to your Defender depends on the version. We have no official source for that.

The Td5 has a 16-pin connector. Through the K-line (an older wire for diagnostics, pin 7 in the port), its also speaks a Land Rover language of its own. In that language, a program first has to log in, with its own maths puzzle as a lock. You can see this in the source code of a freely usable app for the Td5.

What Car-Z can do on the classic Defender

  • Td5 and Puma (2.4 and 2.2): we have not tested these ourselves, and we promise nothing.
  • Want to know whether your Defender answers? The Car-Z connection check is free and shows whether your and your car are talking to each other. That way you know before you take out a subscription.

The new Defender: what you do see

The new Defender speaks standard over , the network the in the car use to talk to each other. Car-Z has been tested on a Defender L663 of model year 2021, a P400e, with a Vgate iCar Pro 4.0. In the drive tests on 16 and 17 November 2026, connecting, , live values and trips worked.

  • Engine and drivetrain : , and . A only disappears once the car itself has seen a few trips without the fault.
  • Live values: on our test car , speed, , intake air, fuel, outside temperature and the voltage of the 12V battery. For free you see , speed, and . With Plus you see everything the car passes on in the full dashboard.
  • The mileage: on the Defender L663 of model years 2020 to 2025, Car-Z reads it from one , if Car-Z knows it is a Defender. We tested that on one car, of model year 2021. There it matched the odometer.
  • Trips: with Basic every trip is saved, with the peaks.

The new Defender: what you don't see

Standard is about the engine and the exhaust gases. Everything Land Rover stores in its own way is not part of it. Think of the temperature of the gearbox or the transfer box, the air suspension and the car's settings.

With Plus, the system scan also asks the other , such as and airbags, for their . On our test car, more than thirty answered the question of who they are. Whether the of all those come through properly, we have not yet tested on the Defender.

Car-Z changes nothing in your car. The app only reads. Changing settings, so-called coding, is not possible with Car-Z.

Model year 2026 and later: Secure Diagnostics

In August 2025, Land Rover introduced Secure Diagnostics on the Defender and the Discovery of model year 2026. According to Land Rover, this restricts diagnostics over the car's network until an approved diagnostic tool unlocks it. Land Rover refers to the international UN rules for cyber security and software updates of cars.

What this means for a standard , Land Rover does not say. We have not tested a Defender of model year 2026. If you have one, try the free connection check. It shows what your car passes on.

The P400e plug-in hybrid

The P400e is the plug-in hybrid: a petrol engine with an electric motor and a 13.1 kWh battery, only as a Defender 110. The engine passes on its data as on every Defender L663.

Through standard , the P400e also gives a percentage for the hybrid battery. On our test car it showed 17 to 20 percent while the car itself reported that the battery was empty. The car probably holds back a reserve. That is why Car-Z calls this value "Hybrid battery (gross)". Car-Z does not read cell voltages or the battery's health.

How to read the new Defender

  1. Find the . On the Defender L663 it is to the left of the pedals, above the footrest.
  2. Plug in the while the car is standing still. Make sure it does not get near your feet or the pedals.
  3. Switch the ignition on, open Car-Z on your phone and connect to the .
  4. Read the . Each code comes with what the car reports, in plain language. A garage makes the diagnosis.
  5. If you drive off, put your phone in a holder. Connect and set things up before you drive off.

Frequently asked questions

Can I read my Td5 with Car-Z?

We have not tested that ourselves, so we don't promise it. The connection check is free: it shows whether your and your Td5 are talking to each other, before you take out a subscription.

Does Car-Z work on my Puma Defender?

We have not tested that either, and we don't promise it. Try the free connection check: it shows whether your and your car are talking to each other.

Why don't I see my gearbox temperature?

That value is not part of standard . Land Rover stores it in its own way. Car-Z only shows what the car passes on through the standard, plus the mileage on the Defender L663 up to and including model year 2025.

Does it work on a Defender of model year 2026?

We don't know yet. From model year 2026, Land Rover secures diagnostics with Secure Diagnostics, and we have not tested such a Defender. The free connection check shows what your car passes on.

Can I change settings on my Defender with Car-Z?

No. Car-Z only reads. You can clear , with a confirmation and only when the car is standing still.

Sources

  1. Directive 98/69/EC, Annex I, point 8: OBD for petrol and diesel cars by category and dateEuropean Union (text on legislation.gov.uk), consulted on 18 November 2026
  2. On-board diagnostics (EOBD: the same connector and protocols; K-line on pin 7)Wikipedia, consulted on 18 November 2026
  3. Land Rover Defender (1983–2016): Td5 from 1998, Puma 2.4 from spring 2007, 2.2 from model year 2012, end of production 29 January 2016Wikipedia, consulted on 18 November 2026
  4. TD5Tester: app for the Td5 engine control unit (K-line, 10,400 baud, login with seed and key)hairyone (GitHub), consulted on 18 November 2026
  5. Land Rover Defender 2007 - 2016: Identifying fault codes (diagnostic connector by the fuses)Haynes, consulted on 18 November 2026
  6. Land Rover Defender (L663): presented 10 September 2019, model year 2020 and later, P400e with a 13.1 kWh batteryWikipedia, consulted on 18 November 2026
  7. General Diagnostic FAQ's (G4142441), question 6: Secure Diagnostics, August 2025, Defender and Discovery 26MY, UN R155 and R156Jaguar Land Rover (TOPIx), consulted on 18 November 2026
  8. OBD-II PIDs: service 01, PID 5B "Hybrid battery pack remaining life"; service 0A permanent codesWikipedia, consulted on 18 November 2026
  9. OBD2 port location in Land Rover Defender (2019 - ...): left of the pedals, above the footrestKlavkarr (user photos), consulted on 18 November 2026

Read it yourself with Car-Z

Put a plug into the OBD port and see on your device what the car itself reports. Testing whether your plug and car work and reading the fault codes is free, without an account.

All articles