In short
- Limp mode is a protective mode. The engine computer sees a fault and limits the power, so that nothing else breaks.
- You notice it by little power, a low top speed or an automatic gearbox that no longer shifts properly. Usually a warning light is on too.
- Drive calmly to a safe place, stop and call your breakdown service or garage. Have the fault code read: it points the garage in the right direction.
What limp mode is
A modern car has a control unit for the engine: a small computer that controls the engine. Through sensors, it keeps an eye on everything, such as the turbo pressure, the accelerator pedal and the temperature.
If the control unit sees a fault that could lead to more damage, it puts the car in limp mode. It then limits the power or the gears. That way you can still drive calmly to a safe place or a garage, and the engine or the gearbox is not damaged further.
There is no fixed warning light for limp mode. Usually the engine light or another light is on. Some cars have their own light or message for reduced engine power.
How you notice it
- The car accelerates poorly, even when you press the accelerator far down.
- It won't go faster than a certain speed. British sources give about 50 km/h as an example, in some cars up to 80 km/h.
- The engine won't rev high. A British breakdown service gives not above 2,000 rpm as an example.
- An automatic gearbox only shifts into a few gears or doesn't shift at all any more.
Common causes and their fault codes
A fault code is a short code that the car stores when something goes wrong, such as P0299. The code says what the car measures, not which part is broken. The garage finds that out. A few examples:
- The turbo. A turbo blows extra air into the engine for more power. If the pressure is too low, the engine may store code P0299 (too little turbo pressure). This can be due to, for example, the turbo itself, a valve in the turbo system or a sensor that measures the pressure.
- The accelerator pedal or the throttle. An electronic accelerator pedal can have two sensors that both measure how far you press it. If their values don't match, the engine may switch to reduced power. One example is code P2138. A fault in the electronic throttle, which controls how much air goes into the engine, can also cause reduced power.
- The automatic gearbox. It has its own control unit. If that sees a fault, it may limit the gears or stop shifting. The engine may then store code P0700: "the gearbox is asking for the engine light". The actual code is in the control unit of the gearbox.
- Other causes that British sources mention: an engine that is too hot, too little oil or too low oil pressure, a weak battery, a broken sensor or wiring.
What you do
- Stay calm and drive carefully to the next safe place, such as a car park. Keep in mind that you accelerate more slowly and can't go as fast as normal.
- Stop and look at which warning lights and messages are on. Look them up in your owner's manual.
- If a red light is on, stop as soon as it is safe. If the engine is too hot, call your breakdown service.
- Contact your garage or your breakdown service. You can also ask them for advice.
- In a safe place, you can switch the engine off, wait a moment and start it again. One manufacturer mentions about half a minute. If it was a short fault, the limp mode may be gone. If the car says that the gearbox may not engage again after switching off, don't do this by the side of the road. Have the car checked in any case: the cause may still be there.
What you'd better not do
- Clearing the fault code to get rid of the limp mode. Clearing repairs nothing. If the fault is still there, the car may go straight back into limp mode.
- Driving on when the car reports that the automatic gearbox is too hot. One manufacturer says for its dual-clutch automatic: stop in a safe place, put the gearbox in P with the engine running and let it cool down. Follow what your owner's manual says.
Why reading the codes helps
The fault code points the garage in the right direction: turbo, accelerator pedal, gearbox or something else. That means less searching.
With the fault code, the car often also stores a freeze frame. This is a snapshot of, among other things, the engine speed, the speed, the coolant temperature and the engine load at the moment the fault occurred. From this, the garage can see under which conditions it went wrong, for example at high speed or with a cold engine.
What Car-Z does and doesn't see
- Even without an account: the engine fault codes, with a short explanation in plain language. These include P0299, P2138 and P0700. Also the live engine speed and speed, and a warning if the engine gets too hot or the battery is no longer being charged.
- With a free account, also the live coolant temperature and battery voltage, and clearing fault codes.
- With Plus: the freeze frame, and the fault codes of the other control units, such as the gearbox's, on cars with CAN (the network the control units use to talk to each other).
- If you clear a code, Car-Z first saves a snapshot of the codes on your device. Clearing is only possible when the car is standing still, with the ignition on and the engine off.
- Car-Z does not make a diagnosis and does not say whether you can drive on. The app shows what your car itself reports. The garage looks for the cause.
Frequently asked questions
Can I keep driving with my car in limp mode?
Limp mode is meant to get you calmly to a safe place, not to keep driving with for long. Stop as soon as it is safe, check your owner's manual and call your breakdown service or garage. With a red light: stop as soon as it is safe.
Does limp mode go away by itself?
It can, after restarting, if it was a short fault. If the fault is still there, the limp mode comes back. Have the car checked in both cases.
My car won't accelerate, but no warning light is on. Is that limp mode too?
It can be. Usually a light is on, but not always. Have the fault codes read and the car checked.
Does clearing the fault code take my car out of limp mode?
Sometimes for a while, but it repairs nothing. If the fault is still there, the car may go straight back into limp mode. Clearing can also erase the freeze frame, and the garage needs it. Only clear after the repair.
Sources
- What is limp mode? Symptoms and causesRAC (United Kingdom), consulted on 18 November 2026
- What is limp mode, why it happens to your car and how to fix itAuto Express (United Kingdom), consulted on 18 November 2026
- Waarschuwingslampje: stoppen of doorrijden?ANWB (Netherlands), consulted on 18 November 2026
- Reduced Engine Power Light (owner's manual Saab 9-7X, US, p. 3-39)Saab (copy on ManualsLib), consulted on 18 November 2026
- DTC P2122, P2123, P2127, P2128 or P2138 (workshop information Saab 9-5, 2011)Saab WIS (online copy), consulted on 18 November 2026
- P2138-00 (workshop information Saab 9-3, 2003)Saab WIS (online copy), consulted on 18 November 2026
- TSB 22-NA-224: Reduced Engine Power, MIL Illuminated, DTCs P0101, P0172, P0299, P0506 and/or P1101 (GMC Terrain 2018)General Motors (copy on CarComplaints, NHTSA number 10226122), consulted on 18 November 2026
- TSB A011516: DTC P0299 (Turbo/Super Charger Underboost) (Audi A3 2006)Audi (copy on CarComplaints, NHTSA number 10119942), consulted on 18 November 2026
- DTC P0700 (workshop information Saab 9-4X, 2011)Saab WIS (online copy), consulted on 18 November 2026
- Transmission Limp Home Mode (owner's manual Ram 2500/3500, US, 2022)Stellantis (Mopar), consulted on 18 November 2026
- Dual-clutch transmission warnings (owner's manual, Canada, 2023)Kia, consulted on 18 November 2026
- Directive 70/220/EEC, Annex XI, Appendix 1: freeze frameEuropean Union (via legislation.gov.uk), consulted on 18 November 2026