Does Car-Z work with your Acura?
What works, from which year, where the port is and what to watch out for.
From which year
With an ordinary plug. Years are model years.
| Fuel | United States |
|---|---|
| Petrol | From 1996 |
| Hybrid or plug-in hybrid | From 2013 |
| Electric | Partly |
Acura wasn't officially sold in Europe; imported cars follow the rules of the market they were built for.
Check your Acura
Choose make, year and fuel. The answer appears right away.
Choose a make and a year to see the answer.
General guidance based on the law and known information per make; not a guarantee for one specific car. You also need a suitable plug and browser: see the guides.
What Car-Z reads
- Live data: speed, revs, temperatures, engine load, boost and more, as far as the car reports them.
- Stored and pending fault codes of the engine and emission-related systems.
- Clearing those codes, always only after you confirm.
- The vehicle identification number (VIN), if the car reports it.
- The 12-volt battery voltage.
What it doesn't do
- Fault codes from modules such as ABS, airbags or body electronics: those are manufacturer-specific.
- Coding, programming, adaptations or service resets.
- Battery health of electric cars and hybrids.
- Keys, immobiliser or odometer.
Where is the OBD2 port?
Look for a 16-pin, trapezoid-shaped socket. Usually:
Under the dashboard on the driver's side, near the pedals or the steering column.
In right-hand-drive cars (UK, Ireland) the port is usually on the driver's side too, but some models keep it on the left.
Security gateway
We know of no security gateway for Acura that affects standard OBD. Newer cars increasingly have one; reading standard OBD stays available, because emission checks depend on it.
Electric and hybrid
Electric cars don't have to support standard OBD. Usually little comes through: the 12-volt voltage works, fault codes and live values often don't.
Hybrids have a combustion engine and therefore full standard OBD. Engine data comes through while the engine runs; battery data is manufacturer-specific.
Protocols per period
Typical for this make; it can differ per model. A good ELM327 plug supports all OBD protocols and picks the right one itself.
- ISO 9141-2 (K-line)1996–2005 · standard OBD
- ISO 14230 KWP2000 (K-line)2000–2008 · standard OBD
- ISO 15765 CANsince 2005 · standard OBD
Good to know
- Acura shares most of its electronics with Honda, so what applies there largely applies here too.
- Hybrids report engine data through standard OBD. Data on the hybrid battery (charge, cell voltages, health) is manufacturer-specific, and the app doesn't read it.
Tested in practice
What we and other drivers found with a real Acura. The rules above are a guideline; this is what actually happened.
No tests with a Acura yet
We haven't tested a Acura ourselves yet and fewer than 3 drivers have shared their results. Drive a Acura? Connect once and share anonymously whether it worked.
| Model and years | Status | What works | Dongle and protocol |
|---|---|---|---|
| All modelsfrom 1996 · Petrol · United States | ExpectedBased on the rules, not tested yet |
| – |
| All modelsfrom 2013 · Hybrid or plug-in hybrid · United States | ExpectedBased on the rules, not tested yet |
| – |
Verified: tested by us or a garage. Reported: at least 3 drivers shared the same result. Expected: follows from the rules, not tested yet.
Frequently asked questions
From which year does Car-Z work with a Acura?
With a standard OBD2 plug: petrol from 1996 in the US. Older cars usually lack standard OBD.
Where is the OBD2 port in a Acura?
Under the dashboard on the driver's side, near the pedals or the steering column.
Can I clear fault codes on my Acura?
Yes, standard engine fault codes can be cleared, always only after you confirm. Note: clearing also resets the readiness monitors, which matters for an emissions test.
Does Car-Z work with an electric Acura?
Partly. Electric cars don't have to support standard OBD, so usually only the 12-volt voltage and a few values come through. Battery health is manufacturer data and isn't shown.
Which plug do I need?
An ordinary, open OBD2 plug with Bluetooth LE that understands the standard ELM327 commands. Not a closed plug that only works with its maker's own app. The guides list which plugs we've tested and how to connect them.
Can Car-Z code or program my Acura?
No. Car-Z reads standard OBD: live data and engine fault codes. Coding, programming and service resets need manufacturer-specific tools.
Sources
How sure we are: Medium: based on reliable sources, with some details per model still uncertain.
Related makes
Ready to read your Acura?
Put a small plug in the port, open the app and connect.