Skip to content
SearchFree account
Menu
Sweden · OBD2 compatibility

Does Car-Z work with your Polestar?

What works, from which year, where the port is and what to watch out for.

From which year

With an ordinary plug. Years are model years.

FuelEurope (incl. UK)United States
Hybrid or plug-in hybridFrom 2019From 2019
ElectricPartlyPartly

Check your Polestar

Choose make, year and fuel. The answer appears right away.

Where was the car sold new?

Choose a make and a year to see the answer.

General guidance based on the law and known information per make; not a guarantee for one specific car. You also need a suitable plug and browser: see the guides.

What Car-Z reads

  • Live data: speed, revs, temperatures, engine load, boost and more, as far as the car reports them.
  • Stored and pending fault codes of the engine and emission-related systems.
  • Clearing those codes, always only after you confirm.
  • The vehicle identification number (VIN), if the car reports it.
  • The 12-volt battery voltage.

What it doesn't do

  • Fault codes from modules such as ABS, airbags or body electronics: those are manufacturer-specific.
  • Coding, programming, adaptations or service resets.
  • Battery health of electric cars and hybrids.
  • Keys, immobiliser or odometer.

Where is the OBD2 port?

Look for a 16-pin, trapezoid-shaped socket. Usually:

Under the dashboard on the driver's side, near the pedals or the steering column.

In right-hand-drive cars (UK, Ireland) the port is usually on the driver's side too, but some models keep it on the left.

Port location per model (Klavkarr) ↗

Security gateway

We know of no for Polestar that affects standard . Newer cars increasingly have one; reading standard stays available, because emission checks depend on it.

Electric and hybrid

Electric cars don't have to support standard . Usually little comes through: the 12-volt voltage works, and live values often don't.

Hybrids have a combustion engine and therefore full standard . Engine data comes through while the engine runs; battery data is manufacturer-specific.

Protocols per period

Typical for this make; it can differ per model. A good plug supports all protocols and picks the right one itself.

  • ISO 15765 CANsince 2019 · standard OBD
  • DoIP (Ethernet)since 2019 · manufacturer tools only

Good to know

  • Polestar shares most of its electronics with Volvo, so what applies there largely applies here too.
  • Polestar makes (almost) only electric cars.
  • Battery health (SoH) and exact state of charge of electric models are manufacturer data, not standard OBD. The app doesn't show them.

Tested in practice

What we and other drivers found with a real Polestar. The rules above are a guideline; this is what actually happened.

No tests with a Polestar yet

We haven't tested a Polestar ourselves yet and fewer than 3 drivers have shared their results. Drive a Polestar? Connect once and share anonymously whether it worked.

Model and yearsStatusWhat worksDongle and protocol
All modelsfrom 2019 · Hybrid or plug-in hybrid · Europe (incl. UK)ExpectedBased on the rules, not tested yet
  • Live data: works
  • Read codes: works
  • Readiness: works
–

Verified: tested by us or a garage. Reported: at least 3 drivers shared the same result. Expected: follows from the rules, not tested yet.

Frequently asked questions

From which year does Car-Z work with a Polestar?

Polestar has no petrol or diesel models with standard OBD in our data. See the electric section above.

Where is the OBD2 port in a Polestar?

Under the dashboard on the driver's side, near the pedals or the steering column.

Can I clear fault codes on my Polestar?

Yes, standard engine fault codes can be cleared, always only after you confirm. Note: clearing also resets the readiness monitors, which matters for an emissions test.

Does Car-Z work with an electric Polestar?

Partly. Electric cars don't have to support standard OBD, so usually only the 12-volt voltage and a few values come through. Battery health is manufacturer data and isn't shown.

Which plug do I need?

An ordinary, open OBD2 plug with Bluetooth LE that understands the standard ELM327 commands. Not a closed plug that only works with its maker's own app. The guides list which plugs we've tested and how to connect them.

Can Car-Z code or program my Polestar?

No. Car-Z reads standard OBD: live data and engine fault codes. Coding, programming and service resets need manufacturer-specific tools.

Sources

  1. OVMS – OBD-II vehicles (EV notes)
  2. Klavkarr – OBD port location Polestar

How sure we are: Medium: based on reliable sources, with some details per model still uncertain.

← All makes

Ready to read your Polestar?

Put a in the port, open the app and connect.