Skip to content
SearchFree account
Menu
Article

Clearing fault codes: when to do it and when not

Clearing turns off the engine warning light, but it fixes nothing. What disappears when you clear codes, when it makes sense and when you are better off leaving them.

Published on 14 November 20266 minute read

In short

  • Clearing turns off the . The cause stays. If the fault is still there, the code comes back.
  • Clearing also removes the and the results of the . Those tests () then say "not ready".
  • Clearing makes sense after a repair, to see if the fault stays away. Not just before the , not with a flashing or red light, and not when you don't know the cause.
  • Save the codes and the before you clear them. Your garage can make good use of them.

What happens when you clear codes

To clear codes, a in the sends one fixed command to the car. In the standard, this is called . It clears the emission data the car has stored. The goes off.

More than just the disappears:

  • The . If your car has , those stay. The car only removes them by itself once it has found that the fault is gone.
  • The : a record of things like the and the at the moment the fault happened.
  • The results of the . The () go back to "not ready". The car runs them again while you drive.

Clearing fixes nothing

The light goes off, but the cause is still there. If the car sees the same fault again during its , often only after a few trips, it stores the code again and the light comes back on.

The other way round, a code sometimes goes away by itself. Under the European rules for the diagnostic system, the light may go off if the fault does not happen for three trips in a row and there is no other fault. The car may clear the code itself if the fault does not come back for at least forty warm-ups of the engine.

When clearing makes sense

In both cases you know what the cause was and you want to test if it is gone. Then you lose little, especially if you saved the codes and the first. Do keep the in mind, see below.

  • After a repair. You clear the codes and drive. If the code stays away and the say "ready" again, the repair probably worked.
  • After you have fixed a simple cause yourself. Then you can see if the code comes back.

When you are better off not clearing

Going to sell the car? Then don't clear the codes just before without saying so. A buyer can see that codes were cleared recently. How that works is in the article about used cars and cleared codes. A separate article about the is coming soon.

  • Just before the . After clearing, the say "not ready". Take the Dutch as an example: if the inspector reads the diagnostic system, that check does not pass and the normal follows after all. How it works in your country, your testing station can tell you.
  • With a flashing . Flashing usually means the engine is so badly that the can be damaged. Stop in a safe place and call your breakdown service.
  • With a red light on the dashboard. Red means: stop and pull over. Clearing does not help then.
  • When you don't know the cause. Then you clear exactly what your garage needs to find the fault.

What your garage loses

For a garage, the and the are the first clues. The code says where the car saw a problem. The shows under which conditions: for example with a cold or warm engine, idling or at speed.

After clearing, that is gone. Only when the fault comes back does the car store a new code and a new . Until then, the garage searches without those clues.

How Car-Z clears codes

Car-Z only sends read commands to the car. Clearing is the only exception. It only happens when you confirm it and the car is standing still.

  1. Park the car. Switch the ignition on and leave the engine off. If the engine is running or the car is moving, you cannot clear codes. The screen tells you why.
  2. Under "", tap "Clear codes".
  3. Step 1 of 2: read what clearing does and doesn't do, and tap "Next".
  4. Step 2 of 2: check which codes will be cleared and tick the box to say you have read the risks. You can add a reason if you like, for example "fixed a hose".
  5. Tap "Clear codes". Car-Z first saves a on your phone, with the codes, the and the if the car provides it. If that fails, nothing is cleared.
  6. Just before clearing, Car-Z checks once more that the car is standing still and the engine is off.

After clearing

Drive a few trips and read the codes again. If a cleared code comes back, Car-Z shows the message "Came back after clearing" with that code. Then something is probably really wrong: have it checked.

Clearing and the before it are free, also without a subscription. Car-Z only sends the standard clear command, which is meant for engine and emission codes. The app does not send a clear command for , airbags or other safety systems. Car-Z also never clears codes by itself: it only happens when you tap the button.

Frequently asked questions

Does the light come back on straight after clearing?

Usually not straight away. The car first has to see the fault again during a while driving. How long that takes differs per fault and per car.

Can I clear permanent codes?

No, if your car has them. Not with a , and not by disconnecting the battery. The car removes a itself once the fault has been fixed and its own test has passed again afterwards.

My car is due for its periodic inspection in a week and the light is on. Should I clear the codes?

Better not. After clearing, the say "not ready". At the Dutch , for example, the normal then follows after all if the inspector reads the diagnostic system. Better have the cause checked before the inspection.

Does Car-Z also clear airbag or ABS codes?

No. Car-Z only sends the standard clear command, which is meant for engine and emission codes. For the airbag, the and other safety systems, go to a garage.

Sources

  1. OBD-II Service Modes ($04 Clear Emissions Related Data, $02 Freeze Frame)Snap-on, diagnostic equipment manual, consulted on 14 November 2026
  2. Directive 70/220/EEC, Annex XI: OBD system (warning light, turning off the light, clearing fault codes)European Union (text on legislation.gov.uk), consulted on 14 November 2026
  3. Geluid en milieu (APK-eisen personenauto's, EOBD-procedure)RDW, APK handbook (Netherlands), consulted on 14 November 2026
  4. Waarschuwingslampje: stoppen of doorrijden?ANWB (Netherlands), consulted on 14 November 2026
  5. Permanent Diagnostic Trouble Codes (ARSC News, Spring 2019)Bureau of Automotive Repair, California, consulted on 14 November 2026
  6. OBD-II PIDs (overview of the data from SAE J1979, service 04)Wikipedia, consulted on 14 November 2026

Read it yourself with Car-Z

Put a plug into the OBD port and see on your device what the car itself reports. Testing whether your plug and car work and reading the fault codes is free, without an account.

All articles