In short
- Clearing fault codes turns off the engine warning light. The fault itself is not fixed.
- Clearing leaves traces: the car's self-tests (readiness) start again, and cars that support it count the distance and engine time since the codes were cleared. Permanent codes cannot be cleared at all.
- With a dongle in the OBD port and your phone, you can read these traces yourself during the viewing.
- A trace is a clue, not proof. A new battery or a repair gives the same picture. Ask the seller what happened.
What clearing does, and what it doesn't
Almost every petrol car sold new in the EU from 2001, and most diesels from 2004, has its own diagnostic system: EOBD. It watches the parts that keep the exhaust gases clean, such as the catalytic converter and the oxygen sensors. If it sees a fault, it stores a fault code and turns on the engine warning light.
Anyone with a dongle can clear those fault codes. The light then goes off. But the cause is still there. If the fault comes back, the light comes on again. Under the European rules, this may take no more than ten trips on average.
So a seller can switch off a warning light for a while. There can be a good reason to clear codes, such as a repair. As a buyer, you still want to know if it happened recently.
You can find out, even without knowing how the car was before. The car keeps its own counters and self-tests, and these start again from zero when codes are cleared. So reading the car once at the seller's is enough. Below are the four traces.
Trace 1: the self-tests say "not ready"
A car tests its own emission systems while you drive: the catalytic converter, the oxygen sensors, the evaporative system (EVAP) and, on a diesel, the particulate filter, for example. For each test, it keeps track of whether it has finished. This is called readiness.
After the codes are cleared, or if the battery has been disconnected, all these tests go back to "not ready". They only become ready again by driving. Some tests need special conditions, such as a certain speed, temperature or engine load. A car that rarely drives like that may take a long time to finish some tests.
If several tests say "not ready" on a car that is driven normally, codes may have been cleared recently, or the battery may have been disconnected. It can also mean that a part is not working properly, so a test cannot run.
Trace 2: distance and time since clearing
Many cars also keep track of how far the car has been driven since the codes were last cleared, how often the engine has warmed up since then and how many minutes it has run. These counters are in SAE J1979, the standard that describes the standard OBD2 data. Not every car reports them.
An example: the odometer shows 140,000 km, but the car reports 12 km since clearing. Then the codes were cleared just before the viewing. If it shows a few thousand kilometres, they were at least not cleared recently. The counter goes up to 65,535 km.
Trace 3: the freeze frame
With the first fault, the car stores a freeze frame: a record of things like the engine speed, the engine load, the coolant temperature and the road speed at the moment the fault happened. A garage can use it to see under which conditions things went wrong.
When the code is cleared, the car may throw the freeze frame away too. So don't count on still seeing it after clearing. If there is a code, the freeze frame tells you more than the code alone. If you find a code with a freeze frame from a cold engine at high revs, you can ask about that directly.
Trace 4: permanent codes
You cannot clear a permanent code: not with a dongle, and not by disconnecting the battery. The car only removes it by itself once the fault has been fixed and the self-test has passed again afterwards.
If you see a permanent code while the light is off, the car has not yet confirmed that the fault is gone. Then the codes were cleared recently or the battery was disconnected, or the car was just repaired and has not driven enough to confirm it. Either way, it is a good question for the seller.
Not every car has permanent codes. In the US state of California, they have counted at the inspection since 2019 for cars from model year 2010. If a car does not report them, an empty list tells you nothing.
How to check it during the viewing
- Switch the ignition on without starting the engine. The engine warning light should now be on, and go off once the engine runs. If it does not light up at all with the ignition on, something is wrong with the light.
- Plug the dongle into the OBD port, open Car-Z on your phone and connect.
- Look at the fault codes: the stored codes, the pending codes and the permanent codes.
- Look at the readiness and the counters since clearing: live in the app with Plus, or in the inspection report of the one-off check. Car-Z puts them together under "Codes recently cleared?".
- Look at the freeze frame for each code, in the same place.
- If in doubt, ask the seller what happened: a new battery, a repair, codes cleared at the garage? A clear story with an invoice is fine.
- Save the result in the inspection report, so you can read it again later or show it to a garage.
What it does and doesn't prove
The traces show that something was cleared recently or that the battery was disconnected. They do not show who did it or why. A garage that clears the codes after a repair, a disconnected or new battery: they all give the same picture. That is normal.
You also cannot see which code was cleared. The code is gone, and often the freeze frame too. And after enough driving, the traces are gone: the self-tests are ready again and the counters go up. How much driving that takes differs from car to car.
Your own history only helps with your own car. With Plus, Car-Z keeps track per car of when you first and last saw a fault code, and whether it comes back. For a used car you don't know yet, you don't have that history. There, you work with what the car itself stores.
The other way round, a car with all tests "ready" and no codes is a good sign, but not a guarantee. The diagnostic system mainly looks at emissions. It does not see brakes, tyres or rust.
- Check the mileage separately, for example in your country's vehicle register, where that is possible. In the Netherlands, the RDW gives a free verdict on whether the recorded odometer readings are logical.
- If a lot of money is involved, also have a pre-purchase inspection done by a garage or an inspection company.
Clearing codes just before the inspection
Every country has its own rules for the periodic inspection. Take the Dutch APK as an example. If a car runs on petrol or diesel, weighs no more than 3,500 kg and was first registered after 2005, the inspector reads the diagnostic system. That passes if the light matches what the system reports, there are no fault codes starting with a P and all self-tests are ready. Then the exhaust gases do not need to be measured. A diesel with a particulate filter is different: there the inspector uses a particle counter to check that the filter works, and reading the system does not replace that.
If the tests are not ready or there are fault codes, the normal exhaust gas test follows. So in the Netherlands, clearing codes just before the APK does not help: the self-tests will then say "not ready".
In Great Britain, the MOT checks that the engine warning light comes on with the ignition and then goes off. On most petrol cars from July 2003 and diesels from July 2008, a light that does not work or shows a fault is a major defect. In other countries, ask your testing station how it works there.
The Car-Z inspection report
Car-Z reads the fault codes, the readiness, the counters since clearing, the distance driven with the light on and the freeze frames. Under "Codes recently cleared?", Car-Z combines these signals into one answer: probably, possibly, unlikely or cannot be determined. If only one test is not ready and the other signals do not point to clearing, the answer is "possibly" at most.
Reading the fault codes, including permanent ones, is free. Readiness, the counters and the freeze frames are in the report of the Car-Z check: on its own for €9.99 per report, or included in Plus. With Plus you also see them live in the app. The report stays on your own phone; you can print it or save it as a PDF.
Frequently asked questions
Can a seller get the self-tests back to "ready"?
Yes, by driving. After enough trips under the right conditions, the tests are ready again, and then the readiness shows nothing. The counters since clearing keep going up, though. If the fault is still there, the code usually comes back, and a permanent code stays until the fault is fixed.
One self-test says "not ready". Is that bad?
Not necessarily. It may be the test of the evaporative system, for example; in California, that one may still be open at the inspection. If more tests are open, or only a short distance has been driven since clearing, ask what happened.
How long does it take before all self-tests are ready?
That differs per car and per test. Most cars finish the tests during normal driving. Some tests need a certain speed, temperature or engine load. A car that rarely drives like that may take a long time to finish those tests.
The garage cleared the codes after a repair. Is that suspicious?
No, that is normal. After a repair the garage clears the codes, and then the self-tests say "not ready" for a while. Ask for the repair invoice, so you know what was done.
Sources
- Geluid en milieu (APK-eisen personenauto's, EOBD-procedure)RDW, APK handbook (Netherlands), consulted on 14 November 2026
- MOT inspection manual for cars and passenger vehicles, section 8: Nuisance (engine MIL)Driver and Vehicle Standards Agency (GOV.UK), consulted on 14 November 2026
- Directive 70/220/EEC, Annex XI: OBD system (warning light, storing and clearing fault codes)European Union (text on legislation.gov.uk), consulted on 14 November 2026
- Directive 70/220/EEC, Annex XI, Appendix 1: freeze frameEuropean Union (text on legislation.gov.uk), consulted on 14 November 2026
- Directive 98/69/EC, Article 2 and Annex I point 8: introduction of OBD for petrol and diesel carsEuropean Union (text on legislation.gov.uk), consulted on 14 November 2026
- Permanent Diagnostic Trouble Codes (ARSC News, Spring 2019)Bureau of Automotive Repair, California, consulted on 14 November 2026
- On-Board Diagnostic Test Reference (readiness and warning light at the inspection)Bureau of Automotive Repair, California, consulted on 14 November 2026
- OBD-II PIDs (overview of the data from SAE J1979)Wikipedia, consulted on 14 November 2026
- Controleer of uw kilometerstand logisch isRDW (Netherlands), consulted on 14 November 2026